Faith-Based Entrepreneurs

Ignite Your Light & Life through the Power of Connection





Better Methods to Prevent Your Customer's Pipes From Freezing

by
web site

Send Feedback to Dr. DeLuke
Print
About Author
Report Problem
Tweet This

Share on Facebook Pin it




When water freezes, it expands. That's why a can of soda explodes if it's put into a freezer to chill quickly and forgotten. When water freezes in a pipe, it expands the same way. If it expands enough, the pipe bursts, water escapes and serious damage results.

Why Pipes Burst:

Surprisingly, ice forming in a pipe does not typically cause a break where the ice blockage occurs. It's not the radial expansion of ice against the wall of the pipe that causes the break. Rather, following a complete ice blockage in a pipe, continued freezing and expansion inside the pipe causes water pressure to increase downstream -- between the ice blockage and a closed faucet at the end. It's this increase in water pressure that leads to pipe failure. Usually the pipe bursts where little or no ice has formed. Upstream from the ice blockage the water can always retreat back towards its source, so there is no pressure build-up to cause a break. Water has to freeze for ice blockages to occur. Pipes that are adequately protected along their entire length by placement within the building's insulation, insulation on the pipe, heating, or water movement within the pipe are safe.

Regional Differences:

Generally, houses in northern climates are built with the water pipes located on the inside of the building insulation, which protects the pipes from subfreezing weather. However, extremely cold weather and holes in the building that allow a flow of cold air to come into contact with pipes can lead to freezing and bursting.

Water pipes in houses in southern climates often are more vulnerable to winter cold spells. The pipes are more likely to be located in unprotected areas outside of the building insulation, and homeowners tend to be less aware of freezing problems, which may occur only once or twice a season.

Pipes in attics, crawl spaces and outside walls are all vulnerable to freezing, especially if there are cracks or openings that allow cold, outside air to flow across the pipes. Research at the University of Illinois has shown that "wind chill" (the cooling effect of air and wind) that causes the human body to lose heat, can play a major role in accelerating ice blockage, and thus bursting, in water pipes.

Holes in an outside wall where television, cable or telephone lines enter can provide access for cold air to reach pipes. The size of pipes and their composition (e.g., copper or PVC) have some bearing on how fast ice forms, but they are relatively minor factors in pipe bursting compared with the absence of heat, pipe insulation and exposure to a flow of subfreezing air.

When is it Cold Enough to Freeze?

When should homeowners be alert to the danger of freezing pipes? That depends on how well your pipes are protected from the cold. The "temperature alert threshold" is 20°F or below.

This threshold is based upon research conducted by the Building Research Council at the University of Illinois. Field tests of residential water systems subjected to winter temperatures demonstrated that, for pipes installed in an unconditioned attic, the onset of freezing occurred when the outside temperature fell to 20°F or below.

This finding was supported by a survey of 71 plumbers, in which the consensus was that burst-pipe problems began to appear when temperatures fell into the teens. However, freezing incidents can occur whenever the temperature is 32° F. ore below. Pipes exposed to cold air (especially flowing air, as on a windy day) because of cracks in an outside wall or lack of insulation are vulnerable to freezing at temperatures above the threshold. However, the 20°F "temperature alert threshold" should address the majority of potential burst-pipe incidents in homes.

Mitigating the Problem:

Water freezes when heat in the water is transferred to subfreezing air. The best way to keep water in pipes from freezing is to slow or stop this transfer of heat.

Ideally, it is best not to expose water pipes to subfreezing temperatures, by placing them only in heated spaces and keeping them out of attics, crawl spaces and vulnerable outside walls. In new construction, proper placement can be designed into the building.

In existing houses, a plumber may be able to re route at-risk pipes to protected areas, although this may not be a practical solution. If the latter is the case, vulnerable pipes that are accessible should be fitted with insulation sleeves or wrapping (which slows the heat transfer), the more insulation the better. It is important not to leave gaps that expose the pipe to cold air. Hardware stores and home centers carry the necessary materials, usually in foam rubber or fiberglass sleeves. Better yet, plumbing supply stores and insulation dealers carry pipe sleeves that feature extra-thick insulation, as much as 1" or 2" thick. The added protection is worth the extra cost.

Cracks and holes in outside walls and foundations near water pipes should be sealed with caulking to keep cold wind away from the pipes. Kitchen and bathroom cabinets can keep warm inside air from reaching pipes under sinks and in adjacent outside walls. It's a good idea to keep cabinet doors open during cold spells to let the warm air circulate around the pipes. Electric heating tapes and cables are available to run along pipes to keep the water from freezing. These must be used with extreme caution; follow the manufacturer's instructions carefully to avoid the risk of fire, and check to make sure the product conforms to UL 2049. Tapes and cables with a built-in thermostat will turn heat on when needed. Tapes without a thermostat have to be plugged in each time heat is needed, and may be forgotten.

Letting the Water Run:

Letting a faucet drip during extreme cold weather can prevent a pipe from bursting. O opening a faucet will provide relief from the excessive pressure that builds between the faucet and any ice blockage (if freezing occurs). If there is no excessive water pressure, there is no burst pipe, even if the water inside the pipe freezes.

A dripping faucet wastes some water, so only pipes vulnerable to freezing (ones that run through an unheated or unprotected space) should be left with the water flowing. The drip can be very slight. Even the slowest drip at normal pressure will provide pressure relief when needed. Where both hot and cold lines serve a spigot, make sure each one contributes to the drip, since both are subjected to freezing. If the dripping stops, leave the faucet(s) open, since a pipe may have frozen and will still need pressure relief.

There is new innovative technology on the market that is easy to install (not requiring pipe cutting or electrical wiring) and a great pipe freezing prevention aid. A temperature controlled thermal convection powered hot water recirculation valve installed at the plumbing fixture at the end of the "at risk plumbing run" (pipes most likely to freeze), will allow water to flow from your water heater-through the existing hot water pipe in the "at risk plumbing run"-to the recirculation valve. From the recirculation valve the water will continue back to the water heater (for reheating)-through the cold water pipe in the "at risk plumbing run". To save hot water, the eco-friendly Hot Water Lobster Instant Hot Water Valve system contains a sensor, which opens the valve only when the water temperature drops below the adjustable temperature setting. This open loop of water circulation keeps temped water circulating through the "at risk plumbing run" without wasting water while it also provides instant hot water, which saves water and saves energy.

If You Suspect a Frozen Pipe:

If you open a faucet and no water comes out, don't take any chances. Call a plumber. If a water pipe bursts, turn off the water at the main shut-off valve (usually at the water meter or where the main line enters the house); leave the faucet(s) open until repairs are completed. Don't try to thaw a frozen pipe with an open flame; as this will damage the pipe and may even start a building fire. You might be able to thaw a pipe with a hand-held hair dryer. Slowly apply heat, starting close to the faucet end of the pipe, with the faucet open. Work toward the coldest section. Don't use electrical appliances while standing in water; you could get electrocuted.

Going on a Trip:

When away from the house for an extended period during the winter, be careful how much you lower the heat. A lower temperature may save on the heating bill, but there could be a disaster if a cold spell strikes and pipes that normally would be safe, freeze and burst.

A solution is to drain the water system. This is the best safeguard. With no water in the pipes, there is no freezing. This remedy should be considered even when the homeowner is not leaving but is concerned about a serious overnight freeze.

To drain the system, shut off the main valve and turn on every water fixture (both hot and cold lines) until water stops running. It's not necessary to leave the fixtures open, since the system is filled mostly with air at that point and not subject to freezing. When returning to the house, turn on the main valve and let each fixture run until the pipes are full again.

Or simply install an eco friendly Hot Water Lobster Instant hot Water Valve!

Dr. Deluke is an L.I.T. Engineer specializing in Environmental Engineering.

Please scroll down to leave a comment below...

Contact the Author

Dr. DeLuke
Water Saving and Energy Saving Articles
Dr. DeLuke's web site

awesome comments



This article has been viewed 254 time(s).

 

 




Be featured on our site and connect with other Christ-centered entrepreneurs.
Click here for details.